Hot selling hot rolling mandrel segment with high quality
For hot rolling
The mandrel is the key part of hot rolling tension reel for coils. Coiling temperature is between 550 to 850ºC. The mandrel has mainly two types: link wedge type and double wedge type.
Link wedge type can also be divided into two kinds: link wedge-coupling drive and link-spline drive.
For link wedge-coupling type tension reel, the mandrel is mainly composed of mandrel body, spreader bar, segment, link, wedge and spreading cylinder. Spreader bar has multistage slopes and segment is supported by multistage wedge. Segment is connected with spreader bar by link so segment does not drop off. With compression spring in the middle of wedge, wedge can firmly contact segment and pyramid surface. There is a gap between the upper surface of wedge and segment, which can reduce the impact of coil head to mandrel during coiling coil. Mandrel body is installed on two bearings. Power is transmitted by crowned-teeth coupling in the real. It is very convenient to dismantle, and due to there is no gear impact during working, mandrel rigidity is improved. It's very beneficial to control the dynamic tension.
The spreading principle of mandrel: spreader bar moves inside mandrel body in axial direction dreivern by hydraulic cylinder, the slant of sperader bar pushes the wedge inside radial hole of mandrel body to move outward. The wedge surface pushes segment to expand outward. Wedge diameter will expand. After coiling coils, spreader bar moves in the opposite direction driven by hydraulic cylinder, and pulls segment to shrink through link. Wedge moves inward and mandrel diameter becomes smaller to discharge state. Then you can begin to discharge coil.
For the two types of link wedge-coupling drive and link wedge-spline drive, the mandrel structures and principles are almost same and the main difference is drive type of mandrel. For link wedge-spline drive type, connection between mandrel and main transmission cases is spline, i.e. insert type. When mouting and dismantling, mandrel can be directly inserted or pulled out of the main transmission cases to achieve the rapid replacement.
The main driving motor drives gear shaft rotation through the intermediate shaft. The gear shaft dirves big gear rotation, and the big gear drives mandrel rotation through spline.
For the double wedge type tension reel, the mandrel is mainly composed of mandrel body, spreader bar, segment, spreader wedge, buffer wege and hyd. Cylinder.
The spreading principle of double wedge type mandrel: hyd. Cylinder makes spreader bar move back and forth in axial direction and the wedge move in radical direction. So the segment becomes big. T-hook on spreader bar pulls wedge back and the hook outside the wedge pulls segment back. This will make the manderel small. With spline connectiion for power transmission unit, mandrel can be rapidly replaced. Cooling water channel inside the mandrel, so cooling effect is good. Lubricant can be injected by auto and manual type, so it can reduce parts wear.
Pay-off reel and tension reel for cold rolling coils are used in cold rolling production line or pay-off when acid pickling,galvanization,annealing,shear,coating or coil tension in out let.
Cold rolling mandrel is the key part of pay-off reel and tension reel. According to different structure, it has beam wedge type, pyramid axis type, pyramid sleeve type, wedge type, radial direction hydraulic cylinder type, etc. Or simply, open type and close type. The close type mandrel is a close circle without gap in the surface after expanding.it is suitable for coiling thin strip steel. The open type mandrel means there is a gap between segments after mandrel expanding, suitable for coiling thicker strip steel.
For cold rolling
Pay-off reel and tension reel for cold rolling coils are used in cold rolling production line or pay-off when acid pickling, gavanization, annealing, shear, coating or coil tension in outlet.
Cold rolling mandrel is the key parts of pay-off reel&tension reel. According to different structure, it has beam wedge type, pyramid axis type, pyramid sleeve type, wedge type, radial direction hydraulic cylinder type, ect. Or simply, open type and close type. The close type mandrel is a close circle without gap in the surface after expanding. It is suitable for coiling thin strip steel. The open type mandrel means there are a gap between segment after mandrel expanding, suitable for coiling thicker strip steel.
The beam wedge type mandrel is mainly composed of the main shaft, expanding core, segment, axial direction wedge, radial direction wedge and spreading cylinder, etc. There are two kinds of structure: with jaw or without jaw. The mandrel with jaw is used for coiling thicker strip steel. It can also be set with steel sleeve or paper sleeve to coil with belt wrapper. The mandrel without jaw is used for coiling thin strip steel by belt wrapper.
The mandrel will move along axial direction driven by the expanding core & wedge block, through relative sliding between the wedge block and segment, swelling and shrinking will occur in radial direction, reset by spring.
The pyramidal axis type mandrel is divided into tapper type and back taper type according to the tilting direction of axis slope. This mandrel has simple structure ,less parts, large main shaft section and high strength .So it can bear large tension, not only coiling ,but also uncoiling. There are two kinds of structure: with jaw or without jaw .it's mainly consisted of the pyramid axis, segment, hollow sleeve and spreading cylinder, etc.
Presently, the back taper type mandrel is the most popular. The oil goes into the cylinder via a rod cavity. The cylinder pulls the pyramidal shaft backward along axial direction and push segment to expand outside, so the drum is expanded. Pyramidal axis moves back ward along axial direction, and segment is pulled back by the T-key, thus the mandrel is shrinked.
KMD introduction:
Location: Yueyang
Established year: 1997
Staffs: 800
Engineer members: 180
Main lines: Electromagnetic liftings, electromagnetic sirrers, magnetic separators, Cable reels, Mandrels,
Oil film bearing seat, etc.
Export countries: over 40 countries including Vietnam, Pakistan, Phillipines, India, Korea, Myanmar, Laos, Thailand, Mylaysia, Russia, Ukrain, Indonesia, Turkey, Spain, USA, etc.
Certifications: CE, ISA, ISO9001
Applications: Metallurgy, Electricity, Mining, Cement industry, Sugar industry, Food, Building materials, Traffic, Light industry, etc.
Welcome to visit our factory!!
Exhibition all over the world
Clients
Guided by managing conception as
Guided the direction by advanced technology,
Exploited the market by perfect service
Building the reputation by excellent quality.
FAQ
Q1.Are you factory?
Yes. We are lifting electromagnet factory, and we also factory for electromagnet stirrer, control cabinet, cable reel, electromagnetic separator, and mandrel since 1997. With 23 years history our clients are more than 2000, and export more than 50 countries. Our plant area is more than 60,000 square meters.
Q2.How fast can i get the quotation?
A: We usually quote within 24 hours after we get your inquiry.If you are very urgent to get the price, please call us or tell us in your email so that we will regard your inquiry priority.
Q3. What's your payment terms?
A: T/T, DP or L/C AT SIGHT for first cooperation..
Q4.Can I get sample before order?
A: Yes, of course. After price confirmation, you can require for samples to check our quality, but the freight is on your site.
Q5. Do you accept OEM?
A: Yes. We accept custom design OEM.
Q6. How do you make our business long-term and good relationship?
A: 1. We keep good quality and competitive price to ensure our customers benefit;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.
Audited Supplier 
){kind=link}